; Mode X (320x240, 256 colors) mode set routine. Works on all VGAs.
; ****************************************************************
; * Revised 6/19/91 to select correct clock; fixes vertical roll *
; * problems on fixed-frequency (IBM 851X-type) monitors.	 *
; ****************************************************************
; C near-callable as:
;	void Set320x240Mode(void);
; Tested with TASM
; Modified from public-domain mode set code by John Bridges.

SC_INDEX	equ	03c4h	;Sequence Controller Index
CRTC_INDEX	equ	03d4h	;CRT Controller Index
MISC_OUTPUT	equ	03c2h	;Miscellaneous Output register
SCREEN_SEG	equ	0a000h	;segment of display memory in mode X

	.model	small
	.data
; Index/data pairs for CRT Controller registers that differ between
; mode 13h and mode X.
CRTParms label	word
	dw	00d06h		;vertical total
	dw	03e07h		;overflow (bit 8 of vertical counts)
	dw	04109h		;cell height (2 to double-scan)
	dw	0ea10h		;v sync start
	dw	0ac11h		;v sync end and protect cr0-cr7
	dw	0df12h		;vertical displayed
	dw	00014h		;turn off dword mode
	dw	0e715h		;v blank start
	dw	00616h		;v blank end
	dw	0e317h		;turn on byte mode
CRT_PARM_LENGTH equ	(($-CRTParms)/2)

	.code
	public	_Set320x240Mode
_Set320x240Mode proc	near
	push	bp		;preserve caller's stack frame
	push	si		;preserve C register vars
	push	di		; (don't count on BIOS preserving anything)

	mov	ax,13h		;let the BIOS set standard 256-color
	int	10h		; mode (320x200 linear)

	mov	dx,SC_INDEX
	mov	ax,0604h
	out	dx,ax		;disable chain4 mode
	mov	ax,0100h
	out	dx,ax		;synchronous reset while setting Misc Output
				; for safety, even though clock unchanged
	mov	dx,MISC_OUTPUT
	mov	al,0e3h
	out	dx,al		;select 25 MHz dot clock & 60 Hz scanning rate

	mov	dx,SC_INDEX
	mov	ax,0300h
	out	dx,ax		;undo reset (restart sequencer)

	mov	dx,CRTC_INDEX	;reprogram the CRT Controller
	mov	al,11h		;VSync End reg contains register write
	out	dx,al		; protect bit
	inc	dx		;CRT Controller Data register
	in	al,dx		;get current VSync End register setting
	and	al,7fh		;remove write protect on various
	out	dx,al		; CRTC registers
	dec	dx		;CRT Controller Index
	cld
	mov	si,offset CRTParms ;point to CRT parameter table
	mov	cx,CRT_PARM_LENGTH ;# of table entries
SetCRTParmsLoop:
	lodsw			;get the next CRT Index/Data pair
	out	dx,ax		;set the next CRT Index/Data pair
	loop	SetCRTParmsLoop

	mov	dx,SC_INDEX
	mov	ax,0f02h
	out	dx,ax		;enable writes to all four planes
	mov	ax,SCREEN_SEG	;now clear all display memory, 8 pixels
	mov	es,ax		; at a time
	sub	di,di		;point ES:DI to display memory
	sub	ax,ax		;clear to zero-value pixels
	mov	cx,8000h	;# of words in display memory
	rep	stosw		;clear all of display memory

	pop	di		;restore C register vars
	pop	si
	pop	bp		;restore caller's stack frame
	ret
_Set320x240Mode endp
	end